







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Cabinets & Countertops in Glendora: What to Expect and What It Costs
Cabinets & countertops in Glendora typically run $14,000 – $45,000 for a full tear-out and replacement, with most homeowners landing between $18,000 and $28,000 when they keep the plumbing where it is and choose mid-grade stock or semi-custom boxes. A straightforward swap on a galley kitchen in the 91740 flats takes two to three weeks; a foothill job where the walls are out of square and the countertop needs a template-and-fab cycle can run five. Call (844) 662-2335, and we’ll walk the kitchen with you and put real numbers on paper before you commit to anything.
How We Take a Glendora Kitchen From Old Boxes to New Stone

This isn’t a “we handle everything” pitch. Here’s the actual order of operations, so you know what’s happening on day one and what you’re deciding on day ten.
Stage 1: Site walk and measure (day 1)
We measure the room, check wall plumb and floor level, and look at where the gas line, the 240V range feed, and the dishwasher drain actually sit. In older 91740 bungalows we find galvanized supply lines and undersized circuits more often than not. You decide here whether we’re keeping the layout or moving anything, because that choice sets everything downstream.
Stage 2: Cabinet spec and order (days 2 – 5, then a 3 – 5 week lead)
You pick the door style, finish, box construction, and drawer hardware. We write the order with pull-out specs and filler widths so nothing gets field-hacked later. KraftMaid is our most-requested semi-custom line because the lead times are predictable. This is where the schedule lives or dies; cabinet lead time is the single biggest driver of when your countertop template can happen. You sign off on the layout drawing here, not later.
Stage 3: Demo, tear-out, and rough-in (3 – 5 days)
Old cabinets come out, and this is where the surprise costs live. Rotted subfloor around a leaking sink, a wall that was never framed plumb, a range hood vented into the attic instead of outside. If plumbing or the circuit has to move, that’s rough-in work in this window, and we tell you the number before we touch it, not after. Walls get patched and primed so the new boxes go up flat.
Stage 4: Cabinet set and countertop template (2 – 4 days, then 7 – 14 days fab)
Base cabinets go in first, shimmed and screwed to the studs, level front to back. Uppers get hung to the layout line. We set a temporary plywood top so you have a working kitchen while the stone cuts. The countertop shop templates once the base run is final, which is the whole reason cabinets install before stone, never the reverse. You pick the edge profile and sink cutout during this window.
Stage 5: Countertop install, sink, and final trim (2 – 3 days)
Stone drops in, the sink gets set and sealed, the dishwasher gets reconnected, and the final trim, toe kicks, and hardware go on. We check every drawer and door for rub, adjust the hinges, and walk the kitchen with you. Final payment happens after that walk, not before.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Actually Choose Between
Most of the decisions on this job come down to five choices, and each one has an honest trade-off.
- Stock vs. semi-custom vs. custom cabinets: Stock is fastest and cheapest but comes in fixed widths, so gaps get filled with panels. Semi-custom (KraftMaid territory) lets you dial widths and finishes for a modest bump and is what most Glendora homeowners land on. Full custom gets you anything you want at a 40 – 60% premium and a longer lead.
- Box material: Plywood boxes hold screws and handle moisture better over the long haul; particleboard is cheaper and fine in dry rooms but swells if a supply line lets go. We’re a plywood-box shop.
- Countertop surface: Quartz is the current default, non-porous and low-maintenance. Granite is durable and cheaper per square foot but needs sealing. Butcher block is warm and forgiving but wants oil a couple times a year. Laminate is a real budget option and looks better than it did ten years ago.
- Edge profile and thickness: A 2cm top with a built-up edge plus a 3cm slab both read thick; the fabricated edge lets you control the look without paying for a full 3cm slab across the whole run.
- Soft-close and drawer hardware: Undermount soft-close glides and hinges add a few hundred dollars and are the difference between a kitchen that feels new and one that feels patched. We default to them.
What Cabinets & Countertops Costs in Glendora, CA

Here are the real Glendora numbers, line-item style, so you can budget before anyone comes out.
| Scope | Typical range |
|---|---|
| Cabinets only (stock or semi-custom, installed) | $4,000 – $13,000 |
| Countertops only (fabricated and installed) | $2,000 – $6,500 |
| Both, standard galley or small L | $14,000 – $22,000 |
| Both, larger kitchen with island or peninsula | $22,000 – $45,000 |
Five things push a Glendora job from the low end to the high end. Size and layout are the biggest: linear feet of cabinetry drives both the boxes and the countertop square footage. Existing condition matters most in older 91740 homes, where rotted subfloor or out-of-plumb walls add repair before install. Relocating plumbing or electrical (moving the sink, moving the range) adds a rough-in stage and a permit. Material grade: a full custom inset kitchen with a 3cm quartz top can double a semi-custom job. Permit scope: a straight cabinet swap usually needs nothing; moving plumbing or a wall does.
Our written estimate lists each line and each allowance. What it doesn’t cover, we say so up front: appliance purchases, and any structural repair we can’t see until the old boxes are off the wall. Those get priced as a change order you approve in writing before work starts. The number you see is the number you pay, and that’s backed by our 730-Day Done Right Promise. If it’s not done right, we make it right.
See the difference
Before
After
Before
After
Before
AfterWhat Glendora Homes Specifically Do to This Job
Glendora splays across two very different building environments, and the kitchen reflects which one it’s in. The flat core around downtown (91740) is mid-century ranch and older bungalows, and that’s where we find the soft subfloor, the out-of-square wall, the 1950s galley that was never designed for a dishwasher. Up in the foothill streets above Sierra Madre Avenue (91741), the 1970s – 1990s custom homes have more generous kitchens, but the sloped-lot construction and canyon runoff mean moisture creeps into toe-kick areas differently, and a lot of those hillside homes sit in the high-fire-hazard zone where the work often gets paired with fire-resistant exterior upgrades. A remodel in 91741 can trigger a permit review the flatland side never sees, which is why we check the parcel before we promise a start date. Permits for cabinet and countertop swaps that don’t touch plumbing, walls, or gas usually aren’t required; once we move a sink drain or the range feed, we pull the permit and pass the inspection. When the scope widens, homeowners often pair this with a Kitchen Remodeling in Glendora, and the same discipline carries into a Garage Conversion ADU in Glendora or a New Detached ADU in Glendora where a kitchenette gets built out. Our Kitchen Remodeling service handles the wider scope, and our crews work across all of Glendora and the neighboring foothill communities.
Serving Glendora, CA – Our Local Coverage Area
We serve Glendora and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Cabinets & Countertops in Glendora

Two to three weeks of active work for a standard kitchen, but plan on the total timeline stretching to six to nine weeks because cabinet and countertop lead times sit between the install stages. Call (844) 662-2335 and we’ll map the schedule for your specific kitchen, lead times included.
Usually not, if you’re swapping boxes and stone in the same footprint without moving plumbing, gas, or walls. The moment a sink drain, range feed, or load-bearing wall moves, a permit applies and we pull it and pass the inspection. Call (844) 662-2335 and we’ll tell you which side of that line your job lands on.
Yes, and it’s the most common way we do it. Keep the sink and range where they are and the job stays a cabinet-and-stone swap with no rough-in stage. It’s also the cheapest path, typically at the low end of the $14,000 – $45,000 range.
Most full jobs land between $14,000 and $45,000, with cabinets alone at $4,000 – $13,000 and countertops alone at $2,000 – $6,500. The variables that move it are size, existing condition, whether plumbing or electrical relocates, and material grade. Call (844) 662-2335 for an exact quote, and the estimate is free.
Every install is covered by our 730-Day Done Right Promise. If it’s not done right, we make it right, on materials and workmanship, for two full years. That’s one of the longer workmanship guarantees you’ll find, and it’s in writing. Call (844) 662-2335 to get started.
Get a Free Estimate on Cabinets & Countertops in Glendora
We’ll come out, measure the kitchen, and put a written line-item number in your hands, no pressure and no vague “it depends.” Call (844) 662-2335 for a free on-site estimate on cabinets & countertops in Glendora. A live person answers around the clock, and we’ll set the walk-through at whatever time works for you.
Written by the team at Groundwork Construction Co..












